This put up about how to make 3 Simple Diy Floating Photo Frames And How to Slash Plexiglass is sponsored by The Household Depot as element of the #THDProSpective Plan. It also includes affiliate back links. See policies.
Simple Do-it-yourself picture frames are truly a person of my most requested tutorials and oddly more than enough, until now, I didn&rsquot have lots of to share!
.
I truly crafted my dad a enormous Diy customized photo body as a Christmas reward a couple a long time ago and shared the tutorial for it below. But it utilised dowels, and a router, and it may well have been a little extra involved than most individuals are seeking for.
So, in this write-up, I&rsquom likely to display you how I designed 3 various design and style Tremendous Straightforward Do-it-yourself floating photo frames with just two essential tools. I&rsquoll also show you how easy it is to cut plexiglass for them, way too!
.
So if you&rsquore prepared to get creating, enable&rsquos go! I&rsquove received the video tutorial below and the action by phase below:
Instruments AND Components:
- Miter noticed (or any wooden reducing saw is good&ndashdoesn&rsquot have to be a MITER noticed)
- Nail Gun (optional, just would make points more quickly)
- Wood Glue
- ¾&Prime square dowels
- one×2 boards
- ¼&Prime x 1 โ &Prime lattice trim
- Slim Plexiglass Sheets
- Ryobi One particular+ HP Lower Off Tool (employed to slash plexiglass)
- Clamps (also optional&ndashif you don&rsquot have clamps, you can use CA glue or painters tape in position of clamps to hold parts whilst wood glue dries)
- Change buttons
A Notice About FLOATING Photograph Frames:
I&rsquom sharing how to make 3 distinct model FLOATING photograph frames in this tutorial, but the to start with move to making any of them is slicing the plexiglass to the size you want.
.
If you don&rsquot want to use plexiglass for your frames, you can skip this stage. But considering the fact that the graphics/photographs I framed are &ldquofloating&rdquo inside the frame, they&rsquore fundamentally sandwiched concerning two parts of plexiglass. So plexiglass/acrylic is essential to be in a position to &ldquofloat&rdquo your photo.
.
To make issues effortless to transform out in these frames, I also used these flip buttons&mdashor I get in touch with them twisty tabs&ndashon the back again to hold the plexiglass in place.  
HOW TO Lower PLEXIGLASS
Normally, I have my community glass shop lower my glass and plexiglass items for my projects.  But considering the fact that these plexiglass items will be smaller and numerous custom sizes, it would be a great deal less costly, quicker and a lot easier to just cut them myself.
.
I utilised some (about) โ &rdquo acrylic sheets from Dwelling Depot.  They occur in various measurements, all the way up to a four×8 sheet.  Get the facts grabbed some 11x14s.
I built some easy graphics on my personal computer (PicMonkey and Canva are great for this!) and also applied a patch that I gained a handful of many years back at a meeting for these frames.  You can use a picture, a poster, fabric, whatsoever you want to body for this.
.
I laid them out on my sheet how I appreciated the spacing, then marked where I wished to slash&ndashno measurements here&hellipjust eyeballing how I considered the spacing all-around the picture seemed good.
Now, I&rsquove applied the inexpensive little hand knife they claim will cut plexiglass before and it was a awful encounter with extremely poor effects.  I&rsquove also employed a jig noticed to slash plexiglass and it melts, gets caught, then chips or cracks the sheet.
.
So THIS time, I tried this new Ryobi A person+ HP Compact Cut Off Instrument with a plastic slicing blade and was carefully amazed with how fast and clean up the cuts ended up.
When I initial saw this tool, I discovered it variety of strange wanting.  But after I used it, I recognized the principle. 
.
It&rsquos generally a hybrid amongst a drill and an angle grinder. It cuts like an angle grinder, but it feels a drill with the head turned ninety levels. 
.
It&rsquos compact and lightweight and it&rsquos got a ahead and reverse swap to flip the blade equally instructions.  It&rsquos also acquired a variable pace induce&mdashwhich is good for reducing plastic to assist prevent melting. 
It arrives with a plastic and drywall blade, a metallic slash off wheel, and a diamond blade for chopping tile and cement board.  You can discover additional about the new Ryboi One+ HP cut off instrument at the website link here if you&rsquore intrigued.
.
For slicing straight strains on the plexiglass, I just lined up a straight edge (scrap piece of wooden), clamped and ran the metallic blade guard from it to make the slash.  You can skip the straight edge and freehand these cuts, as well if you have a continuous hand. (I don&rsquot haha!)
I did find it slice most effective in this circumstance with the switch in reverse. It appeared to not soften that way.
.
I lower two pieces similar in size for each individual item I was framing. Then, I was all set to begin making the true floating image frames.
Simple Diy FLOATING Image Body Type one
Fashion 1 is my individual favorite, so I&rsquoll start out with it ๐
This individual floating photograph body design and style necessitates ¾&Primary square dowels and one×2 board. It is mainly just a 1×2 wrapped all over a square dowel frame.
.
I applied ¾&rdquo sq. dowels for this and set up my miter noticed to slice 45 degrees.  Now, you don&rsquot have to miter these.  You can leave it on 90 and make butt joints.  You also don&rsquot need to have a MITER observed for this.  Any saw that you can lower quite straight with will work good.
.
I basically trimmed four parts of square dowel so that when in shape alongside one another, they&rsquod be just scarcely (like โ &Prime) bigger than the plexiglass piece I was placing in it.
I used wood glue to the corners and nailed them alongside one another with brad nails.  If you are affected person, and don&rsquot have a nail gun, simply glue and clamp until eventually dry.
.
Right after the glue had dried, I minimize to in good shape one×2 pieces with forty five diploma mitered corners all-around this frame.  Again, butt joints are fantastic in this article if you want to skip the mitered corners.
.
I glued and nailed these 1x2s all over the edges leaving about ¼&rdquo sticking out the back again aspect of the plexiglass, so that when I put in the two โ &Primary plexiglass items, it&rsquoll be flush across the back again facet of the frame.
Then, I screwed these twisty tabs into the back again sides of the body to keep the plexiglass in spot.  I&rsquoll go back again and cleanse the sawdust off the plexiglass later on, but for now, I established this off to the aspect to make the next body.
Easy Do-it-yourself FLOATING Photograph FRAMES Design and style two
Type 2 is a tiny simpler and is built of 1x2s and ¼&rdquo thick by one โ &Prime huge lattice trim.
I began by slicing down the lattice parts so it would make a frame that the plexiglass would match Inside of.  Again, just like before, the mitered corners are optional.
As soon as I had this lattice frame slash, I calculated its over-all sizing and slice 1×2 pieces to make a body whose general dimensions matched that of the lattice frame. See below 1×2 body laying on major of lattice body&ndashthey&rsquore the very same sizing.
I glued and nailed the 1×2 frame with each other and clamped right until dry. Yet again, you can use super glue or painters tape if you don&rsquot have a nail gun or clamps ๐
.
Then, I flipped it upside down and glued the lattice frame onto the back again.  I applied a weighty object to maintain it in spot until finally it was dry, then, I screwed twisty tabs on the again to maintain the plexiglass in spot. 
Because the lattice is ¼&rdquo thick, and the plexiglass is โ &rdquo thick, when the two plexiglass pieces are positioned inside, almost everything really should sit flush throughout the back just like the very last frame.
All over again, I&rsquoll go again and clean up the sawdust off later on, but for now, I moved on to the previous style frame.
Effortless Diy FLOATING Picture Body Model three
Style 3 is the same principle as model one, but rather of working with 1x2s, I employed ¼&Key x one โ &Prime lattice trim to maintain the body a very little thinner and far more minimalist searching.
So, I minimize ¾&rdquo sq. dowels to make a body the very same measurement or slightly greater than the plexiglass I was framing and glued and nailed it collectively.
Then, I slice lattice trim to wrap all-around that body. 
I glued the lattice trim on so that there was about ¼&rdquo sticking off the back side of the sq. dowel frame so that when the two pieces of โ &rdquo plexiglass are installed, it&rsquoll all be flush across the again.
.
I didn&rsquot have any brad nails small plenty of to nail this frame on, so I only glued and clamped right up until it was dry.
If you don&rsquot have clamps, you can use painters tape to type of wrap all around the pieces to hold right until the glue dries OR simply just use some tremendous glue or CA glue to assist maintain pieces in place right until the actual wood glue is cured.
.
Then, just like the previous two frames, I put in twisty tabs to keep the plexiglass in place.
FLOATING Image Body HANGING Options
The remaining phase is cleanse up and hanging.  I utilised some glass cleaner to clean up all the saw dust, then utilized a piece of double sided tape on the back again plexiglass piece to make confident the photos stay in place, then put the frames back jointly.
.
To cling, you can use your standard sawtooth hangers for this.
Or simply position it on a shelf.
.
OR, use a drill to drill holes into the corners to run some paracord and hold it on a piece of wood dowel you screwed into the wall.
As you can see, creating photograph frames doesn&rsquot have to be complicated.  This is a fantastic novice venture you can deal with with minimum resources and get as resourceful as you want. 
.
I basically hung these graphics up in my desk spot to assistance continue to keep me determined although working alone from dwelling appropriate now. So, now that my desk space is comprehensive, I guess I should really probably get back again to work ๐
I hope you&rsquove appreciated this very little undertaking.  There are a great deal far more coming your way, so be sure to subscribe to my newsletter beneath so you don&rsquot miss out on what&rsquos coming up coming!
.
And don&rsquot ignore to pin this for afterwards!
Until upcoming time, happy constructing ๐